i was wondering if this combo would be a good idea a EVO Nelly Turbo, plasmatomic engine, and li-ion's?
Mongo, to clear up any confusion, AM is NOT Atomic. AM doesn't make any products, and Atomic is a huge comany that makes parts.
I think he know that; he just meant AM is expensive. :?
I'm editing my post...just for you. :wink:
:lol:
~Junk ET
[quote:9ca3a15b9a="Mongo"]Too expensive for my tastes.
For your taste? Hah! It's just a rip-off! :lol:
I think hardly anyone that isn't new to Xmods doesn't shop at AM. :wink:
~Junk ET
Could that be any more confusing, lol? It took me about 2 minutes to figure out what you were trying to say.
Mongo, to clear up any confusion, AM is NOT Atomic. AM doesn't make any products, and Atomic is a huge comany that makes parts.
Too expensive for my tastes.
For your taste? Hah! It's just a rip-off! :lol:
I think only the newer modders shop at AM; after a while you figure out that AM just buys from other dealers and sells the stuff for 10 bucks more. :wink:
~Junk ET
an atomic chilli
Wish minizworkshop was still around. :cry:
Not sure what a chilli is.
:wink:
~Junk ET
an atomic chilli
what about The nelly turbo and a chilli w/ 4.8v nickel metal hydroxide?
Not sure what a chilli is.
Ni-MH is a step below Li-ion. They have a lower amp draw.
Alkaline = bad
Ni-MH = OK (stock)
Li-ion = Better
Li-poly = Best
:D
what about The nelly turbo and a chilli w/ 4.8v nickel metal hydroxide?
I would use Li-Ion to get the best out of that motor; it's 35 turns.
~Junk ET
what about The nelly turbo and a chilli w/ 4.8v nickel metal hydroxide?
Yeah, a Plasmatomic is going to pull alot, and Lith-ions aren't going to keep up with the current draw. The 2c lipo kits AM sells are perfect, but a bit pricey (for me at least, lol)
Later,
RedSXmodder
Then I would look at Li-Poly with a high C rating (Max amp draw).
yes
Please be more descriptive in your subject titles.
Also, it's a motor, not an engine. It dies not burn fossil fuel. :wink:
Li-poly would be a better combo, I believe the plasma requires alot of amps, Li-ions may not be able to deliver it.
Are you thinking of a 2 cell setup?
I knew someone would say something about our Off-Topic-Ness...
Anyway, running the Plasmatomic (26T motor) on NiMh cells wouldn't be a good idea. I have a 26T motor and it heats up the cells like icecream in your car on a hot sunny summer day.
Plasmatomic~26T
Atomic Chili~35T
The Chili would be fine on stock (EVO) FETs and on NiMh's (for short run times).
Really, below 40T is where you shouldn't use NiMh's. Then AA Li-Ion shouldn't be run on <30T motors.
I ran my 26T motor on Li-Ion and got some great performance but the cells got a little warm after a minute or two of driving.
Like Cowboy said; go for LiPo with a Plasmatomic.
Here's just straight answers:
Plasmatomic~LiPo
Atomic Chili~LiPo, Li-Ion, or NiMh
The Chili (being a 35T) would get about 25MPH on NiMh.
The Plasmatomic realistically gets 40MPH or so on LiPo.
Your best bet is definatly the Plasmatomic on LiPo.
~Junk ET
You know, this kind of gets on my nerves a bit....the off topic rambling really bothers new people who are looking for some answers.
As for your question, The Plasmatomic would be a bit faster than the Chili at both 4.8 and 7.4 volts but in a perfect world you should get Li-Po cells to run either. Li-Po's have a much better discharge than Li-Ions. :wink: If you plan on useable speed, i'd just find a good couple sets of Ni-MH cells since some of these even have a better discharge rate than Li-Ion cells.
I have a Mini-Z that at 4.8 volts(intellect 750mAh) still gets about 30mph with a Plasmatomic. :wink:
Mmmm. VomitChip, my favorite! :lol:
Here you go...

But just remember, I never wanted to give it to you.
Ya' jerk...
:lol:
~Junk ET

EDIT: Apparently the picky guy doesn't like chocolate chip...
He really deserves a vomit cookie now.......
You spelled "for" incorrectly. Or just does not make sense in that sentence, at all. So, start editing, again.
[quote:c3bdd86fc3="Incorrect Junk"]....and sells the stuff or 10 bucks more.
:D Can I have a cookie now?